Difference between revisions of "Layer 3 (CGEMBOSS)"
m |
m (→Mapping overview) |
||
| Line 24: | Line 24: | ||
FEB_label=70, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side) | FEB_label=70, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side) | ||
FEB_label=79, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side) | FEB_label=79, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side) | ||
| + | |||
| + | The following strips are not connected to any channel because they are routed in the anode foil to empty pins of the anode-FEB connector: | ||
| + | |||
| + | X-strips (782, 783) from anode connector coupled to FEB 52 (last connector of 1st anode foil, IN side) | ||
| + | X-strips (784, 785) from anode connector coupled to FEB 70 (last connector of 1st anode foil, OUT side) | ||
| + | X-strips (1614, 1615) from anode connector coupled to FEB 61 (last connector of 2nd anode foil, IN side) | ||
| + | X-strips (1616, 1617) from anode connector coupled to FEB 79 (last connector of 2nd anode foil, OUT side) | ||
===Strip-X=== | ===Strip-X=== | ||
Revision as of 01:29, 16 September 2023
In this page the relation between Layer 3 strips (strip-X, strip-V) and electronics channels (FEB_label and GEMROC-TIGER) is shown. This is the mapping matching the convention used in CGEMBOSS.
Contents
Mapping overview[edit | edit source]
Layer 3 has 1664 strip-X (0-1663) and 2790 strip-V (0-2789). It is divided into two sheets so strips are divided into two equal parts:
Sheet 0: strip-X (0-831), strip-V (0-1394) Sheet 1: strip-X (832-1663), strip-V (1395-2789)
All Layer 3 FEBs channels follow the same order, according to the pinout shown here: L3 FEB pinout
Only channels 0-61 of each chip are connected to a strip (ch. 62-63 are disconnected):
chip 1 reads 14 strip-X and 48 strip-V chip 2 reads 32 strip-X and 30 strip-V
The following channels are not connected to any strip because the correspondent FEB is connected to the last connector of the anode foil:
FEB_label=52, chip 1 --> ch. 61, 40, 52, 50 (V-strip, last FEB of 1st anode foil, IN side) FEB_label=61, chip 1 --> ch. 61, 40, 52, 50 (V-strip, last FEB of 2nd anode foil, IN side) FEB_label=70, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side) FEB_label=79, chip 1 --> ch. 61, 40, 52, 50, 45 (V-strip, last FEB of 2nd anode foil, OUT side)
The following strips are not connected to any channel because they are routed in the anode foil to empty pins of the anode-FEB connector:
X-strips (782, 783) from anode connector coupled to FEB 52 (last connector of 1st anode foil, IN side) X-strips (784, 785) from anode connector coupled to FEB 70 (last connector of 1st anode foil, OUT side) X-strips (1614, 1615) from anode connector coupled to FEB 61 (last connector of 2nd anode foil, IN side) X-strips (1616, 1617) from anode connector coupled to FEB 79 (last connector of 2nd anode foil, OUT side)
Strip-X[edit | edit source]
Sheet 0: strip-X (0-831) Sheet 1: strip-X (832-1663)
Sheet 0[edit | edit source]
| Strips | FEB label | GEMROC | TIGER | Strips_sheet |
|---|
Sheet 1[edit | edit source]
| Strips | FEB label | GEMROC | TIGER | Strips_sheet |
|---|
Strip-V[edit | edit source]
Sheet 0: strip-V (0-1394) Sheet 1: strip-V (1395-2789)
Sheet 0[edit | edit source]
| Strips | FEB label | GEMROC | TIGER | Strips_sheet |
|---|
The connector with one less strip is marked in bold
Sheet 1[edit | edit source]
| Strips | FEB label | GEMROC | TIGER | Strips_sheet |
|---|
The connector with one less strip is marked in bold
